Difference between revisions of "Getting Started with Schematic Layout Editor"
(Created page with " '''Set Up Sheet for Construction''' Open '''Schematic Layout Editor''' Select Imperial Icon on left side for '''Inches''' Select Page Setting from Upper Toolbar Select S...") |
|||
| (2 intermediate revisions by the same user not shown) | |||
| Line 2: | Line 2: | ||
'''Set Up Sheet for Construction''' | '''Set Up Sheet for Construction''' | ||
| − | Open '''Schematic Layout Editor''' | + | 1. Open '''Schematic Layout Editor''' |
| − | Select Imperial Icon on left side for '''Inches''' | + | 2. Select Imperial Icon on left side for '''Inches''' |
| − | Select Page Setting from Upper Toolbar | + | 3. Select Page Setting from Upper Toolbar |
| − | Select Size: '''A 8.5x11in''' | + | 4. Select Size: '''A 8.5x11in''' |
| − | Orientation: '''Landscape''' | + | 5. Orientation: '''Landscape''' |
| − | Enter Revision: '''1A''' | + | 6. Enter Revision: '''1A''' |
| − | Enter Title '''Real Time Clock PCF85263AT/AJ''' | + | 7. Enter Title '''Real Time Clock PCF85263AT/AJ''' |
| − | Click on '''OK''' when done | + | 8. Click on '''OK''' when done |
[[File:KiCad-PageSettings.PNG|400px]] | [[File:KiCad-PageSettings.PNG|400px]] | ||
'''Adding Components & Assigning Footprints''' | '''Adding Components & Assigning Footprints''' | ||
| − | Select from Right Toolbar '''Place Symbol''' | + | 1. Select from Right Toolbar '''Place Symbol''' |
| − | Click Mouse on Grid (Symbols Libraries will load) | + | 2. Click Mouse on Grid (Symbols Libraries will load) |
| − | Type in Search Field '''conn''' | + | 3. Type in Search Field '''conn''' |
| − | Select '''Conn_01x06_Male''' then click OK | + | 4. Select '''Conn_01x06_Male''' then click OK |
| − | Place in Sector '''B1''' Hit ESC Key. | + | 5. Place in Sector '''B1''' Hit ESC Key. |
| − | Select '''Annotate''' Icon from Upper Toolbar. Click on '''Annotate''' tab. | + | 6. Select '''Annotate''' Icon from Upper Toolbar. Click on '''Annotate''' tab. |
| − | Select '''Assign PCB Footprint to Schematic Symbol''' Icon from Upper Toolbar. | + | 7. Select '''Assign PCB Footprint to Schematic Symbol''' Icon from Upper Toolbar. |
| − | After Footprints load select '''J1 Conn_01x06_Male''' then select from Left Column '''Connector_PinHeader_2.54mm''' | + | 8. After Footprints load select '''J1 Conn_01x06_Male''' then select from Left Column '''Connector_PinHeader_2.54mm''' |
| − | Select Line item '''20 Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical''' as seen in Figure 2 | + | 9. Select Line item '''20 Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical''' as seen in Figure 2 |
| − | Repeat | + | Repeat these steps for adding all component symbol. |
[[File:KiCad-AssignFootprint.PNG |800px ]] | [[File:KiCad-AssignFootprint.PNG |800px ]] | ||
| Line 36: | Line 36: | ||
---- | ---- | ||
| − | ==[[KiCad 5.0]]== | + | ==[[KiCad 5.0]]== |
Latest revision as of 21:42, 24 March 2019
Set Up Sheet for Construction
1. Open Schematic Layout Editor
2. Select Imperial Icon on left side for Inches
3. Select Page Setting from Upper Toolbar
4. Select Size: A 8.5x11in
5. Orientation: Landscape
6. Enter Revision: 1A
7. Enter Title Real Time Clock PCF85263AT/AJ
8. Click on OK when done
Adding Components & Assigning Footprints
1. Select from Right Toolbar Place Symbol 2. Click Mouse on Grid (Symbols Libraries will load) 3. Type in Search Field conn 4. Select Conn_01x06_Male then click OK 5. Place in Sector B1 Hit ESC Key. 6. Select Annotate Icon from Upper Toolbar. Click on Annotate tab. 7. Select Assign PCB Footprint to Schematic Symbol Icon from Upper Toolbar. 8. After Footprints load select J1 Conn_01x06_Male then select from Left Column Connector_PinHeader_2.54mm 9. Select Line item 20 Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical as seen in Figure 2 Repeat these steps for adding all component symbol.
Figure 2
Generate Netlist
Select Generate Netlist from the Upper Toolbar. click on Generate Netlist - Save File Continue on to : ==Getting Started with PCB layout Editor ==
