Difference between revisions of "Initializing the Microcontroller"
| (6 intermediate revisions by the same user not shown) | |||
| Line 8: | Line 8: | ||
Unplug any USB Power before programming the Microcontroller. | Unplug any USB Power before programming the Microcontroller. | ||
Plug the '''USBTiny''' Programmer into the '''AVR-ISP 6 pin header''' '''J7'''. | Plug the '''USBTiny''' Programmer into the '''AVR-ISP 6 pin header''' '''J7'''. | ||
| − | Place the '''Jumper''' across '''J8''' to use the '''USBTiny''' 5 volt power. Make sure no other power source is connected! | + | Place the '''Jumper''' across '''J8''' on the Power-Failure-Logger PCB to use the '''USBTiny''' 5 volt power. Make sure no other power source is connected! |
| − | Using '''AVRDUDE''' Validate the '''USBTiny''' is communicating with the Power Fail Module | + | Using '''AVRDUDE''' Validate the '''USBTiny''' is communicating with the Power Fail Module PCB. |
Type the following command in the Windows terminal. | Type the following command in the Windows terminal. | ||
'''avrdude -c usbtiny -p m328p '''<BR> | '''avrdude -c usbtiny -p m328p '''<BR> | ||
| Line 26: | Line 26: | ||
The Microcontroller is set to '''1HMz''' and needs to be changed to '''16 MHz Default''' | The Microcontroller is set to '''1HMz''' and needs to be changed to '''16 MHz Default''' | ||
Enter the following AVRDude command to set the fuse bits on the Microcontroller. | Enter the following AVRDude command to set the fuse bits on the Microcontroller. | ||
| − | |||
'''avrdude -p m328p -c usbtiny -v -U lfuse:w:0xFF:m -U hfuse:w:0xDE:m -U efuse:w:0xFF:m''' | '''avrdude -p m328p -c usbtiny -v -U lfuse:w:0xFF:m -U hfuse:w:0xDE:m -U efuse:w:0xFF:m''' | ||
| Line 41: | Line 40: | ||
==[[ AVRDUDE Class]]== | ==[[ AVRDUDE Class]]== | ||
| − | '''ADD SD Card Reader''' | + | '''ADD SD Card Reader'''<br> |
| − | Insert '''SD Card Reader''' module into the '''Power Logger PCB''' at J6. <br> | + | Insert '''SD Card Reader''' module into the '''Power Logger PCB''' at '''J6'''. <br> |
| + | Make sure the '''Arduino IDE''' has the following libraries installed before programming the board: | ||
| + | #include <SPI.h> // SPI Interface that the SD card module will use. | ||
| + | #include <SD.h> // Library for the SD card. | ||
| + | |||
[[File:SD-Card-Power-Fail.PNG |350px]] | [[File:SD-Card-Power-Fail.PNG |350px]] | ||
| − | Next step '''Setting | + | '''Next step:''' Setting Time and Date for the DS3231 RTC. Click on link below |
| − | ==[[Setting Time and Date for the DS3231 RTC]]== | + | ==[[ Power Fail Logger by Microrusty ]]== |
| + | ==[[Initializing the Microcontroller]]== | ||
| + | ==[[Setting Time and Date for the DS3231 RTC]]== | ||
==[[ Programming Power Fail Logger with Arduino IDE]]== | ==[[ Programming Power Fail Logger with Arduino IDE]]== | ||
| + | ==[[Installation and use]]== | ||
---- | ---- | ||
| − | ==[[ | + | ==[[ Main Page ]]== |
Latest revision as of 21:45, 17 August 2021
Tools needed for programming the Power-Failure-Logger:
USBTiny or USBasp Programmer (refer to AVRDude Class for more information on Programmers) Any RS232 to USB interface. I used the Silicon Labs Prolific CP210x USB to UART Bridge. Digital volt meter
Setting up the ATMega328 chip
Unplug any USB Power before programming the Microcontroller. Plug the USBTiny Programmer into the AVR-ISP 6 pin header J7. Place the Jumper across J8 on the Power-Failure-Logger PCB to use the USBTiny 5 volt power. Make sure no other power source is connected! Using AVRDUDE Validate the USBTiny is communicating with the Power Fail Module PCB. Type the following command in the Windows terminal. avrdude -c usbtiny -p m328p
Connected and Working properly should match this picture.
Trouble shooting any connection issues to the microcontroller refer back to the AVRDude Class. The link is below. If you get the following error message in AVRDUDE see trouble shooting. avrdude: initialization failed, rc=-1
Trouble shooting
USBTiny does not connect with the ATmega Chip. Check the following: Is a Jumper connected across J8. ATMega328 chip is plug in correctly into the socket. USBTiny is powered on. USBTiny is visible in Device Manager under LibUSB-Win32 Devices
Setting the Microcontroller to 16MHz
The Microcontroller is set to 1HMz and needs to be changed to 16 MHz Default Enter the following AVRDude command to set the fuse bits on the Microcontroller. avrdude -p m328p -c usbtiny -v -U lfuse:w:0xFF:m -U hfuse:w:0xDE:m -U efuse:w:0xFF:m Validate the fuses are now set correctly by using the following AVRDUDE command: avrdude -c usbtiny -p m328p -v
Make sure the microcontroller matches these settings: avrdude: safemode: hfuse reads as DE avrdude: safemode: efuse reads as FF avrdude: safemode: Fuses OK (E:FF, H:DE, L:FF) avrdude done. Thank you. For more information about using AVRDude refer back to this link ==AVRDUDE Class==
ADD SD Card Reader
Insert SD Card Reader module into the Power Logger PCB at J6.
Make sure the Arduino IDE has the following libraries installed before programming the board:
#include <SPI.h> // SPI Interface that the SD card module will use. #include <SD.h> // Library for the SD card.
Next step: Setting Time and Date for the DS3231 RTC. Click on link below
