AVR-Programmers

ArduinoISP (Offical Board)

RETIRED The Arduino ISP is a tiny AVR-ISP (in-system programmer) based on David Mellis' project FabISP. With this programmer you can upload sketches and burn the bootloader on any AVR based boards, including Arduinos.

---

ArduinoISP_Home_Made

Home Made Arduino Uno Shield ISP Programmer

AVRdude names:

arduinoisp

Refer to the 2015 AVR workshop:
AVR Programming Part 2 Target Boards

---

AVRISP mk II

The AVRISP mk.II is Atmel's official programmer for the AVR line of chips.

This product is no longer available for sale. For a replacement, see the Atmel-ICE: ATATMEL-ICE

AVRdude names:

avrisp2    avrispmkii

The AVRISP mkII does not provide power on the VCC pin, but uses this pin to sense the voltage on the
target board. Your target board circuit needs to be powered by external means to operate.
When the AVRISP mkII is connected to both the PC and the target board the main status LED should be
green indicating that target power has been detected. AVRISP mkII is now ready to be used with AVRdude
programming command line software.

AVRISP mkII UserGuide

Test the connection to programmer: avrdude -p m328p -c avrisp2 -v or use this: avrdude -p m328p -c avrispmkii -v
The status light changes from Green to Red in AVRdude Terminal mode
Test Terminal Mode: avrdude -p m328p -c avrispmkii -t
dump flash 0 1024
dump eeprom 0 1024
q to exit terminal mode

---

USBasp

USBasp - USB programmer for Atmel AVR controllers USBasp is a USB in-circuit programmer for Atmel AVR controllers. It simply consists of an ATMega88 or an ATMega8 and a couple of passive components. The programmer uses a firmware-only USB driver, no special USB controller is needed.
https://www.fischl.de/usbasp/

AVRdude names:

usbasp   usbasp-clone 

Test the connection to programmer: avrdude -p m328p -c usbasp -v or avrdude -p m328p -c usbasp-clone -v
The status light changes from Green to Red in AVRdude Terminal mode
Test Terminal Mode: avrdude -p m328p -c usbasp -t
dump flash 0 1024
dump eeprom 0 1024
q to exit terminal mode

---

USBtiny (Adafruit)

USBtiny is a software implementation of the USB low-speed protocol for the Atmel ATtiny microcontrollers. Of course, it will also work on the ATmega series. The software is written for an AVR clocked at 12 MHz. At this frequency, each bit on the USB bus takes 8 clock cycles, and with a lot of trickery, it is possible to decode and encode the USB waveforms by software. The USB driver needs approximately 1250 to 1350 bytes of flash space (excluding the optional identification strings), depending on the configuration and compiler version, and 46 bytes RAM (excluding stack space). The C interface consists of 3 to 5 functions, depending on the configuration.

AVRdude name:

usbtiny 

Test the connection to programmer: avrdude -p m328p -c usbtiny -v
The status light changes from Green to Red in AVRdude Terminal mode
Test Terminal Mode: avrdude -p m328p -c usbtiny -t
dump flash 0 1024
dump eeprom 0 1024
q to exit terminal mode

---

Other Programmers:

atmelice     = ICE (ARM/AVR) in ISP mode 
buspirate    = The Bus Pirate
pickit2      = PICkit2 Programmer
stk500       = STK500
xplainedmini = AVR XplainedMini in ISP mode

Link for all supported AVRdude Programming devices:
AVRdude Programmer Lists

---