Difference between revisions of "CW Practice Oscillator Kit"
| Line 3: | Line 3: | ||
[[File:3D-CW-Code-Practice-Osc.PNG |300px ]] | [[File:3D-CW-Code-Practice-Osc.PNG |300px ]] | ||
| − | I decided to make a CW practice board for Morse Code training for my local HAM club. I have donated all 10 boards to the club. | + | I decided to make a '''CW practice board for Morse Code training''' for my local HAM club. I have donated all 10 boards to the club. |
It was a simple process to use KiCad 7.0 to design the board. | It was a simple process to use KiCad 7.0 to design the board. | ||
I am not going to explain how to use KiCad in this wiki page since I have other wiki pages explaining how to use KiCad.<br> | I am not going to explain how to use KiCad in this wiki page since I have other wiki pages explaining how to use KiCad.<br> | ||
| − | This project uses a NE555 timer SMD SOIC-8 Chip that produces a square wave that can be adjusted between 300Hz and 1KHz | + | This project uses a '''NE555 timer SMD SOIC-8 Chip''' that produces a square wave that can be adjusted between '''300Hz''' and '''1KHz''' |
The power source is a 9Volt battery that is connected to J2 via a 9V BATTERY STRAP from Mouser Electronics. | The power source is a 9Volt battery that is connected to J2 via a 9V BATTERY STRAP from Mouser Electronics. | ||
This Kit was designed to be adjustable for the user to change to the tone to their preferred listening levels. | This Kit was designed to be adjustable for the user to change to the tone to their preferred listening levels. | ||
RV4 is a 200K ohm variable resistor that controls the tone between 300Hz to 1KHz. | RV4 is a 200K ohm variable resistor that controls the tone between 300Hz to 1KHz. | ||
RV3 is a 100 Ohm variable resistor that controls the volume. | RV3 is a 100 Ohm variable resistor that controls the volume. | ||
| − | The CW key is connected to a 5mm Terminal block that is label CW Key | + | The '''CW key''' is connected to a '''5mm Terminal block''' that is label CW Key |
| − | This Kit comes with a 55mm Speaker that is connected J3 and placed underneath the bottom of the PCB. | + | This Kit comes with a 55mm Speaker that is connected '''J3''' and placed underneath the bottom of the PCB. |
There is another speaker connector that uses a 5mm Terminal block with the label Speaker for larger speakers. | There is another speaker connector that uses a 5mm Terminal block with the label Speaker for larger speakers. | ||
Revision as of 03:47, 23 February 2024
Code Practice Oscillator
I decided to make a CW practice board for Morse Code training for my local HAM club. I have donated all 10 boards to the club. It was a simple process to use KiCad 7.0 to design the board. I am not going to explain how to use KiCad in this wiki page since I have other wiki pages explaining how to use KiCad.
This project uses a NE555 timer SMD SOIC-8 Chip that produces a square wave that can be adjusted between 300Hz and 1KHz The power source is a 9Volt battery that is connected to J2 via a 9V BATTERY STRAP from Mouser Electronics. This Kit was designed to be adjustable for the user to change to the tone to their preferred listening levels. RV4 is a 200K ohm variable resistor that controls the tone between 300Hz to 1KHz. RV3 is a 100 Ohm variable resistor that controls the volume. The CW key is connected to a 5mm Terminal block that is label CW Key This Kit comes with a 55mm Speaker that is connected J3 and placed underneath the bottom of the PCB. There is another speaker connector that uses a 5mm Terminal block with the label Speaker for larger speakers.
