Getting Started with Schematic Layout Editor - Revision history

U731219879 rc at 21:42, 24 March 2019

2019-03-24T21:42:15Z

U731219879 rc at 21:41, 24 March 2019

2019-03-24T21:41:19Z

U731219879 rc at 21:39, 24 March 2019

2019-03-24T21:39:58Z

U731219879 rc: Created page with " '''Set Up Sheet for Construction''' Open '''Schematic Layout Editor''' Select Imperial Icon on left side for '''Inches''' Select Page Setting from Upper Toolbar Select S..."

2019-03-22T03:10:47Z

Created page with " '''Set Up Sheet for Construction''' Open '''Schematic Layout Editor''' Select Imperial Icon on left side for '''Inches''' Select Page Setting from Upper Toolbar Select S..."

New page

'''Set Up Sheet for Construction'''

Open '''Schematic Layout Editor'''
Select Imperial Icon on left side for '''Inches'''
Select Page Setting from Upper Toolbar
Select Size: '''A 8.5x11in'''
Orientation: '''Landscape'''
Enter Revision: '''1A'''
Enter Title '''Real Time Clock PCF85263AT/AJ'''
Click on '''OK''' when done
[[File:KiCad-PageSettings.PNG|400px]]

'''Adding Components & Assigning Footprints'''
Select from Right Toolbar '''Place Symbol'''
Click Mouse on Grid (Symbols Libraries will load)
Type in Search Field '''conn'''
Select '''Conn_01x06_Male''' then click OK
Place in Sector '''B1''' Hit ESC Key.
Select '''Annotate''' Icon from Upper Toolbar. Click on '''Annotate''' tab.
Select '''Assign PCB Footprint to Schematic Symbol''' Icon from Upper Toolbar.
After Footprints load select '''J1 Conn_01x06_Male''' then select from Left Column '''Connector_PinHeader_2.54mm'''
Select Line item '''20 Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical''' as seen in Figure 2
Repeat Steps for all components.

[[File:KiCad-AssignFootprint.PNG |800px ]]
Figure 2

'''Generate Netlist'''

Select '''Generate Netlist''' from the Upper Toolbar. click on '''Generate Netlist''' - '''Save''' File
Continue on to :
==[[Getting Started with PCB layout Editor]] ==

----
==[[KiCad 5.0]]==<br>

← Older revision		Revision as of 21:42, 24 March 2019
Line 36:		Line 36:

	----		----
−	==[[KiCad 5.0]]==~~<br>~~	+	==[[KiCad 5.0]]==

@@ Line 22: / Line 22: @@
 .  After Footprints load select '''J1 Conn_01x06_Male'''  then select from Left Column '''Connector_PinHeader_2.54mm'''
 .  Select Line item '''20 Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical''' as seen in Figure 2
-  Repeat Steps for all components.
+  Repeat these steps for adding all component symbol.
   [[File:KiCad-AssignFootprint.PNG |800px ]]

@@ Line 2: / Line 2: @@
 '''Set Up Sheet for Construction'''
-  Open '''Schematic Layout Editor'''
+.  Open '''Schematic Layout Editor'''
-  Select Imperial Icon on left side for '''Inches'''
+.  Select Imperial Icon on left side for '''Inches'''
-  Select Page Setting from Upper Toolbar
+.  Select Page Setting from Upper Toolbar
-  Select Size: '''A 8.5x11in'''
+.  Select Size: '''A 8.5x11in'''
-  Orientation: '''Landscape'''
+.  Orientation: '''Landscape'''
-  Enter Revision: '''1A'''
+.  Enter Revision: '''1A'''
-  Enter Title '''Real Time Clock PCF85263AT/AJ'''
+.  Enter Title '''Real Time Clock PCF85263AT/AJ'''
-  Click on '''OK''' when done
+.  Click on '''OK''' when done
   [[File:KiCad-PageSettings.PNG|400px]]
 '''Adding Components & Assigning Footprints'''
-  Select from Right Toolbar '''Place Symbol'''
+.  Select from Right Toolbar '''Place Symbol'''
-  Click Mouse on Grid (Symbols Libraries will load)
+.  Click Mouse on Grid (Symbols Libraries will load)
-  Type in Search Field '''conn'''
+.  Type in Search Field '''conn'''
-  Select '''Conn_01x06_Male''' then click OK
+.  Select '''Conn_01x06_Male''' then click OK
-  Place in Sector '''B1''' Hit ESC Key.
+.  Place in Sector '''B1''' Hit ESC Key.
-  Select '''Annotate''' Icon from Upper Toolbar. Click on '''Annotate''' tab.
+.  Select '''Annotate''' Icon from Upper Toolbar. Click on '''Annotate''' tab.
-  Select '''Assign PCB Footprint to Schematic Symbol''' Icon from Upper Toolbar.
+.  Select '''Assign PCB Footprint to Schematic Symbol''' Icon from Upper Toolbar.
-  After Footprints load select '''J1 Conn_01x06_Male'''  then select from Left Column '''Connector_PinHeader_2.54mm'''
+.  After Footprints load select '''J1 Conn_01x06_Male'''  then select from Left Column '''Connector_PinHeader_2.54mm'''
-  Select Line item '''20 Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical''' as seen in Figure 2
+.  Select Line item '''20 Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical''' as seen in Figure 2
   Repeat Steps for all components.