View source for Connecting the components in the schematic

'''Connect +5 VCC'''
 Open '''Schematic Layout Editor'''
 Select '''Place Wire''' from right side tool bar.
 Draw a wire from the '''Pin 6''' of the 6 Pin Connector to '''Pin 8''' of the RTC
 Select '''R1''' and move to connect to the wire that was just created.
 Select '''R2''' and move to connect to the wire that was just created.
 Select Place Symbol and then type '''VCC''' in pop up search window and click on OK. . 
 Place just above the wire as seen in picture below
 [[File:Figure2.PNG |350px ]]
'''Connecting the Clock Crystal'''
 Select '''Global Label''' right side tool bar and type '''OSCO''' in the text field.
 Rotate and connect to '''Pin 2''' of RTC. 
 Hover over label and hit '''C''' key to '''Copy''' the label and then connect the copy to '''Pin 2''' of the Crystal.
 Select '''Global Label''' and type '''OSC''' in the text field. Rotate and connect to '''Pin 1''' of RTC. 
 Hover over label and hit '''C''' key to '''Copy''' the label and then connect the copy to '''Pin 1''' of the Crystal.
 As seen in picture below
 [[File:Figure3.PNG |250px ]]
'''Connecting I2C SDA & SCL''' 
 Select '''Place Wire''' from right side tool bar.
 Draw a wire from the '''Pin 4''' of the 6 Pin Connector to '''SCL Pin 6''' of the RTC 
 Draw a wire from the '''Pin 3''' of the 6 Pin Connector to '''SDA Pin 5''' of the RTC
 Draw a wire from the bottom '''R1''' and connect to the wire running from '''Pin 4 to PIN 6 (SCL)''' of the RTC
 Draw a wire from the bottom '''R2''' and connect to the wire running from '''Pin 3 to PIN 5 (SDA)''' of the RTC
 As seen in picture below
 [[File:Figure4.PNG |350px ]]
'''Connecting the INTA''' 
 Select '''Global Label''' right side tool bar and type '''INTA''' in the text field.
 Rotate and connect to '''Pin 2''' of the '''6 Pin''' Connector. 
 Hover over label and hit '''C''' key to '''Copy''' the label and then connect the copy to '''Pin 7''' of the RTC.
 Select and Move R3 to connect bottom between the new label INTA and Pin 7 on the RTC.
 Hover over the VCC symbol and hit '''C''' key to '''Copy''' the '''VCC symbol''' and then connect the '''VCC symbol''' to the 
 top of '''R3'''
 As seen in Figure below.
 [[File:Figure5.PNG |450px ]]
'''Finishing up and adding the Ground''' 
 Select '''Place Symbol''' and then type '''GND''' in pop up search window and click on OK. 
 Connect '''GND''' symbol to '''Pin 1''' of the '''6 Pin''' connector. 
 Select '''Place Wire''' from right side tool bar.
 Draw wire from '''Pin 1''' on 6 pin connector to '''Pin 4''' on RTC. 
 Hover over the '''GND''' symbol and hit '''C''' key to '''Copy''' the '''GND symbol''' 
 Select '''r''' to '''rotate''' the symbol and connect to '''Pin 5''' of the '''6 Pin''' connector.
 Hover over the '''GND''' symbol and hit '''C''' key to '''Copy''' the '''GND symbol''' again.
 Connect '''GND''' to bottom of '''C1''' 
 Hover over the '''VCC''' symbol and hit '''C''' key to '''Copy''' the '''VCC symbol''' 
 Connect the '''VCC '''symbol to the top of '''C1'''
 [[File:Figure6.PNG |350px ]]
'''Connecting the optional Battery'''
 Hover over the '''GND''' symbol and hit '''C''' key to '''Copy''' the '''GND symbol''' again.
 Connect '''GND''' to bottom of '''C2''' 
 Select '''Global Label''' right side tool bar and type '''VBAT''' in the text field.
 Rotate and connect label to '''Pin 3''' of the RTC.
 Hover over the '''VBAT''' label and hit '''C''' key to '''Copy''' the '''VBAT label'''
 Connect '''VBAT label''' to top of '''C2'''
 [[File:Figure7.PNG |150px ]]

 '''Generate Netlist'''
 1. From '''Schematic Layout Editor''' 
 2. Select from Top Toolbar '''Generate Netlist''' 
 3. From Popup select '''Generate Netlist''' 
 4. Select '''Save'''

 Now lets position the '''[[ Component layout on PCB  ]]'''
----
==[[ KiCad 5.0 ]]==